Design of high frequency buck converter for DC Motor Control

L. Xheladini; A. Polat; L. T. Ergene

doi:10.1109/OPTIM.2015.7426961

Design of high frequency buck converter for DC Motor Control

L. Xheladini, A. Polat, L. T. Ergene

Department of Electrical Engineering

Istanbul Technical University

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

1 Citation (Scopus)

Abstract

In this project, following a brief historical view on the control methods of DC motors and the first high power semiconductor devices, the mathematical models of different DC motors and buck converter are derived first. Using these equations, a high frequency buck converter is designed according to the model of the DC motor used in the experimental section. After that, using the designed converter, characteristics of shunt and series DC motors are derived for several operating conditions. The characteristics of the DC motors are followed by the influence of the load change to the output voltage of the converter and its efficiency change as the load is increased.

Original language	English
Title of host publication	Joint International Conference - ACEMP 2015
Subtitle of host publication	Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems
Editors	H. Bulent Ertan
Publisher	Institute of Electrical and Electronics Engineers Inc.
Pages	768-773
Number of pages	6
ISBN (Electronic)	9781467372398
DOIs	https://doi.org/10.1109/OPTIM.2015.7426961
Publication status	Published - 7 Mar 2016
Event	1st Joint International Aegean Conference on Electrical Machines and Power Electronics, ACEMP 2015, International Conference on Optimization of Electrical and Electronic Equipment, OPTIM 2015 and International Symposium on Advanced Electromechanical Motion Systems, ELECTROMOTION 2015 - Side, Turkey Duration: 2 Sept 2015 → 4 Sept 2015

Publication series

Name	Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems

Conference

Conference	1st Joint International Aegean Conference on Electrical Machines and Power Electronics, ACEMP 2015, International Conference on Optimization of Electrical and Electronic Equipment, OPTIM 2015 and International Symposium on Advanced Electromechanical Motion Systems, ELECTROMOTION 2015
Country/Territory	Turkey
City	Side
Period	2/09/15 → 4/09/15

Bibliographical note

Publisher Copyright:
© 2015 IEEE.

Keywords

buck converter
efficiency
Series/Shunt DC Motor
speed
torque

UN SDGs

This output contributes to the following UN Sustainable Development Goals (SDGs)

Access to Document

10.1109/OPTIM.2015.7426961

Cite this

Xheladini, L., Polat, A., & Ergene, L. T. (2016). Design of high frequency buck converter for DC Motor Control. In H. B. Ertan (Ed.), Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems (pp. 768-773). Article 7426961 (Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems). Institute of Electrical and Electronics Engineers Inc.. https://doi.org/10.1109/OPTIM.2015.7426961

Xheladini, L. ; Polat, A. ; Ergene, L. T. / Design of high frequency buck converter for DC Motor Control. Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems. editor / H. Bulent Ertan. Institute of Electrical and Electronics Engineers Inc., 2016. pp. 768-773 (Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems).

@inproceedings{5f2f1fe02e364fc79da30d718ee9e7ee,

title = "Design of high frequency buck converter for DC Motor Control",

abstract = "In this project, following a brief historical view on the control methods of DC motors and the first high power semiconductor devices, the mathematical models of different DC motors and buck converter are derived first. Using these equations, a high frequency buck converter is designed according to the model of the DC motor used in the experimental section. After that, using the designed converter, characteristics of shunt and series DC motors are derived for several operating conditions. The characteristics of the DC motors are followed by the influence of the load change to the output voltage of the converter and its efficiency change as the load is increased.",

keywords = "buck converter, efficiency, Series/Shunt DC Motor, speed, torque",

author = "L. Xheladini and A. Polat and Ergene, {L. T.}",

note = "Publisher Copyright: {\textcopyright} 2015 IEEE.; 1st Joint International Aegean Conference on Electrical Machines and Power Electronics, ACEMP 2015, International Conference on Optimization of Electrical and Electronic Equipment, OPTIM 2015 and International Symposium on Advanced Electromechanical Motion Systems, ELECTROMOTION 2015 ; Conference date: 02-09-2015 Through 04-09-2015",

year = "2016",

month = mar,

day = "7",

doi = "10.1109/OPTIM.2015.7426961",

language = "English",

series = "Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems",

publisher = "Institute of Electrical and Electronics Engineers Inc.",

pages = "768--773",

editor = "Ertan, {H. Bulent}",

booktitle = "Joint International Conference - ACEMP 2015",

address = "United States",

}

Xheladini, L, Polat, A & Ergene, LT 2016, Design of high frequency buck converter for DC Motor Control. in HB Ertan (ed.), Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems., 7426961, Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems, Institute of Electrical and Electronics Engineers Inc., pp. 768-773, 1st Joint International Aegean Conference on Electrical Machines and Power Electronics, ACEMP 2015, International Conference on Optimization of Electrical and Electronic Equipment, OPTIM 2015 and International Symposium on Advanced Electromechanical Motion Systems, ELECTROMOTION 2015, Side, Turkey, 2/09/15. https://doi.org/10.1109/OPTIM.2015.7426961

Design of high frequency buck converter for DC Motor Control. / Xheladini, L.; Polat, A.; Ergene, L. T.
Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems. ed. / H. Bulent Ertan. Institute of Electrical and Electronics Engineers Inc., 2016. p. 768-773 7426961 (Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems).

Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review

TY - GEN

T1 - Design of high frequency buck converter for DC Motor Control

AU - Xheladini, L.

AU - Polat, A.

AU - Ergene, L. T.

PY - 2016/3/7

Y1 - 2016/3/7

N2 - In this project, following a brief historical view on the control methods of DC motors and the first high power semiconductor devices, the mathematical models of different DC motors and buck converter are derived first. Using these equations, a high frequency buck converter is designed according to the model of the DC motor used in the experimental section. After that, using the designed converter, characteristics of shunt and series DC motors are derived for several operating conditions. The characteristics of the DC motors are followed by the influence of the load change to the output voltage of the converter and its efficiency change as the load is increased.

AB - In this project, following a brief historical view on the control methods of DC motors and the first high power semiconductor devices, the mathematical models of different DC motors and buck converter are derived first. Using these equations, a high frequency buck converter is designed according to the model of the DC motor used in the experimental section. After that, using the designed converter, characteristics of shunt and series DC motors are derived for several operating conditions. The characteristics of the DC motors are followed by the influence of the load change to the output voltage of the converter and its efficiency change as the load is increased.

KW - buck converter

KW - efficiency

KW - Series/Shunt DC Motor

KW - speed

KW - torque

UR - http://www.scopus.com/inward/record.url?scp=84964937546&partnerID=8YFLogxK

U2 - 10.1109/OPTIM.2015.7426961

DO - 10.1109/OPTIM.2015.7426961

M3 - Conference contribution

AN - SCOPUS:84964937546

T3 - Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems

SP - 768

EP - 773

BT - Joint International Conference - ACEMP 2015

A2 - Ertan, H. Bulent

PB - Institute of Electrical and Electronics Engineers Inc.

T2 - 1st Joint International Aegean Conference on Electrical Machines and Power Electronics, ACEMP 2015, International Conference on Optimization of Electrical and Electronic Equipment, OPTIM 2015 and International Symposium on Advanced Electromechanical Motion Systems, ELECTROMOTION 2015

Y2 - 2 September 2015 through 4 September 2015

ER -

Xheladini L, Polat A, Ergene LT. Design of high frequency buck converter for DC Motor Control. In Ertan HB, editor, Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems. Institute of Electrical and Electronics Engineers Inc. 2016. p. 768-773. 7426961. (Joint International Conference - ACEMP 2015: Aegean Conference on Electrical Machines and Power Electronics, OPTIM 2015: Optimization of Electrical and Electronic Equipment and ELECTROMOTION 2015: International Symposium on Advanced Electromechanical Motion Systems). doi: 10.1109/OPTIM.2015.7426961

Design of high frequency buck converter for DC Motor Control

Abstract

Publication series

Conference

Bibliographical note

Keywords

UN SDGs

Access to Document

Other files and links

Fingerprint

Cite this